E10-npn+ PLC
Description
The new E10-npn+ PLC is an enhanced version of the E10-npn. All timers and counters in the E10+ now support the full range of set values from 0-9999 instead of just 0-254, and the maximum program steps have been increased to 216 steps compared to just 90 steps in the original E10. More importantly, the E10+ PLCs can now be programmed by the new WinTRiLOGI version 3.5 software which runs under Windows 95/98/ME/NT/2000 and XP.

The new E10+ PLC also has a jumper-selectable RS232 / RS485 port with programmable baud rate, and supports a full set of host link commands similar to those on the H- and the M-series PLCs. This PLC can thus be used as a slave I/O board for a host PC or as remote I/Os of an M-series PLC. The new E10-npn+ employs 1/8 power RS485 driver and hence up to 248 E10-npn+ can be networked to a single host PC or PLC.

NOTE FOR NEW CUSTOMERS : please purchase PLC Starter Kit which includes i-TRiLOGI programming software.

 

Pricing & Availbility:

Buy Now

Request for Pricelist (PDF)

  • Key Features
  • Specification
  • Documentation
  • Application
  • Review
  • Peripherals
Finally, a Ladder-Logic based PLC so small and cost so little that it can effectively replace all those bulky relays, timers or counters found in your current control panels. Its 24V DC transistor outputs or 0 to 250V AC relay outputs eliminate the need for additional driver circuitry and its incredibly low price means you actually save money while getting a technically superior design for your next control panel project!

With their built-in RS485 interface, the new E10+ PLCs are ideal for distributed control where the I/Os are distributed to far away locations. The RS485 standard interface allows a twisted pair wire to connect PLCs at up to 1200 m (4000 ft) away! Up to 255 E10+ PLCs may be connected to a master PLC such as the T100MD+ or to a host PC using the Auto485. Each E10+ PLC can work standalone for fast local control and at the same time, their I/O status can be remotely controlled and monitored by the master PLC or by a PC. Its simple ASCII based Host Link Commands are really easy to use. You can see a Visual BASIC example HERE

An E10+ PLC is programmable using an extremely user-friendly ladder logic editor-cum-simulator software - WinTRiLOGI Version 3.5. This software now runs under Windows operating systems (95,98,ME, NT,2000,XP). The same PC can be used to program either a single E10+ via RS232 interface, or up to 255 E10+ PLCs via the RS485 network.

WinTRiLOGI runs on any Windows PC. Featuring pull-down menus, pop-up windows and on-line contextsensitive help systems, TRiLOGI is the most user-friendly ladder logic editor available. Its built-in logic SIMULATOR allows you to perform complete off-line testing of your program on your PC screen without connecting to the target PLC. You can immediately verify our claim by downloading the evaluation copy of the TRiLOGI from our Internet Website: http://www.tri-plc.com/trilogi.htm and finish writing the ladder program for your next project in no time!
- Digital Input: 6 (24V npn)
- Digital Output (peak current): 4 (1A npn)
- Digital I/O Expansion: -
- Analog I/O: -
        A.I. Interface -
        A.O. Interface -
- PWM (current): -
- Stepper Motor Controller: -
- Stepper Motor Drivers: -
- High Speed Counter: -
- RS232 ports: 1 (shared with RS485)
- RS485 port (2-wire): 1 (shared with RS232)
- 14-pin LCD port: -
- Ethernet Port: -
- IR Remote Control: -
- Light Dimmer control: -
- Program Flash Memory: -
- Non-volatie FRAM: -
- Dimension (L x W x H): 2.13” x 2.13” x 0.79”
- Operating Temperature: 0-70 ℃
- Power Supply DC 12 to 24V (+ 10% ripple), Current 0.5~2A (load dependent)
E10-npn+ Product Brochure (View PDF)
E10-npn+ Installation Guide (View PDF)
E10+ PLC Host Link Command Reference Manual (View PDF)
Coming Soon
DIN-KIT-1B - Din Rail Mounting Kit
U-485 - USB to RS485 Serial Port Converter
Auto485 - RS232-to-RS485 Converter
DB9 Cable - DB9 Programming Cable
MDR-6024 - Power Supply, 24VDC, 2.5A